Name: Village of Norridge Cruise Night RC Racing Series
Start: 2026-06-25T17:00:00-05:00
End: 2026-06-25T21:00:00-05:00
Location: 7740 W Montrose Ave, Norridge, IL 60706

Village of Norridge Cruise Night RC Racing Series

The Village of Norridge, Damore Motorsports, and Kenosha R/C are excited to announce the first annual Norridge Cruise Night RC Racing Series!
Muscle Cars, Music, Food Trucks, and RC Racing excitement!
This will be a five race points series starting Thursday June 25th and running once a month until October 15th. Please bring a table, chairs, and extension cords. There is no supplied power, we will have a generator on hand, but additional generators would be appreciated.
Event Start Time: 5:00 PM
First race: 6:00 PM
Classes (Rules at the very bottom of the description):
-Rookie
-Losi NASCAR (Box Stock)
-ARRMA Mojave (Box Stock)
-Stock Super Trucks (Box Stock Traxxas Slash/ARRMA Fury)
-Vintage Trans-AM
Entree:
$20 First Class
$5 Each Additional Class

===CLASS RULES===
Losi NASCAR (Box Stock)
-These are "Box Stock" classes. All parts must remain as the manufacturer intended unless otherwise permitted in the rules listed below.
The Box Stock & Rookie classes will all run the same exact rules, but must adjust the throttle limiter on the back of the Spektrum SLT2 radio to the proper percentage based on the class
-Box Stock- 100%
-Rookie - 50% (Rookie Class)
Chassis:
-Stock Losi Tub Chassis
-No added weight, anywhere or of any kind.
-No cutting or grinding the chassis or any of the parts that attach to it for any reason. The top deck/center brace must remain in tack as delivered from the factory. All the screws must be used in the top deck/center brace.
-M4 washers may be used on the screws under the front splitter to keep the screws from pulling through the bumper. The screw head must not stick out past the outer part of the splitter.
Electronics:
-Stock electronics only
-Radio: Spektrum SLT2
-ESC/Receiver: Spektrum 2-in-1
-SPMXSE3125RX (1st Gen, Y-adapter needed for Transponder)
-SPMXSE3325RX (2nd Gen "Earnhardt Cars", no Y-adapter needed)
-Servo: Spektrum SX110 SPMSSX110
-Battery: Spektrum SPMX142S30HS 1400mAh
-Motor: Losi 28T 380 Sized Brushed Motor
-Motor Fan: Any 25mm fan is allowed, fan shrouds are not allowed
Gearing / Motor Plate:
-Stock 59T spur, 19T pinion gears
Shocks:
-Any shock oil may be used. No internal limiters are allowed. The stock 2.5mm bump stop is the only bump stop allowed. There must be 10mm between the bottom of the shock and the eyelet when fully extended and the shock must be able to compress all the way to the 2.5mm bump stop. Original black springs only, no upgrade springs, no cutting the springs.
Differentials:
-Grease may be changed in the differentials but must remain free spinning. For tech, we will be spinning the tires, they must cause a differential action in the opposite tire without spinning the motor over. If you spin a tire by hand and the motor spins, then the differential isn't legal.
Bearings:
Stock bearings only
Tire and Wheel:
-Losi
-Medium - LOS-1914
-Soft - LOS-1937
-Gluing the sidewall of the tires are permitted.
-No Solid Wheel Dot Decals or Rim Inserts allowed
Bodies:
-Losi
-Chevrolet Camaro ZL1 - LOS-1938
-Toyota Camry - LOS-1918
-Ford Mustang Dark Horse - LOS-1917
-Proline Racing
-1996 Chevy Monte Carlo - PRO371317
-1990 Chevy Lumina - PRO370917
-1996 Ford Thunderbird - PRO371017
-Losi/Proline Racing stock car bodies only, no other manufacturers (SuperRad, Exotek, McAllister, etc.) Proline Racing Dodge Viper bodies are not allowed.
-Proline Racing NASCAR Craftsman Truck Series Bodies not allowed in Cup or Grand National, they will only be permitted to be used in the Losi NASTRUCK (Brushless) class.
-Any paint scheme is allowed but a racing theme is encouraged. You must have a number on the roof and door panels.
-The body must be in the stock location and height. No trimming or lighting the body.
Approved upgrades and adjustments:
-Any weight shock oil
-Gluing the sidewall of the tires is permitted
-Any 25mm fan is allowed
-Losi heat sink Part #LOS-1920
-Losi Aluminum servo horn part #LOS-1910
-3D Printed switch relocates/transponder mounts are legal
-------------------------
ARRMA Mojave GROM

Chassis:
-ARRMA Mojave GROM Chassis
-No added weight, anywhere or of any kind.
-No cutting or grinding the chassis or any of the parts that attach to it for any reason. The top deck/center brace must remain in tack as delivered from the factory. All the screws must be used in the top deck/center brace.
-All parts must remain as the manufacturer intended.
Electronics:
-Radio: Any Spektrum Radio may be paired with the stock electronics or you may use the stock Spektrum SLT2
-ESC/Receiver: Spektrum 2-in-1 - SPMXSE2625RX (Y-adapter needed for Transponder)
-Servo: Spektrum SX110 SPMSSX110
-Battery: Spektrum SPMX142S30HS 1400mAh
-Motor: ARRMA 28T 380 Sized Brushed Motor
-Motor Fan: Any 25mm fan is allowed
Gearing / Motor Plate:
-59t spur, 19T pinion gear
Shocks:
-Any shock oil may be used. No internal limiters are allowed. Original black springs only, no upgrade springs, no cutting the springs.
Differentials:
-Upgraded ARRMA metal gear diffs are allowed. Grease may be changed in the differentials but must spin freely, no locked diffs.
-The body must be in the stock location and height. Full Interior and driver figures are required. No trimming or lightening the body.
Approved upgrades and adjustments:
-Any Spektrum Radio paired with stock electronics
-Assembled Oil Filled Differential 30T 0.8Mod - ARA311193
-Metal Axle & Wheel Hex Set - ARA311231
-Any weight shock oil.
-Gluing/Taping the sidewall of the tires are permitted.
-After market 25mm fan
-ARRMA heat sink Part #ARA-1419
-Aluminum servo horn part #LOS-1910
-3D Printed transponder mounts are legal
-------------------------
Stock Stadium Trucks (Short Course Trucks)
Chassis:
-Brushed 2WD Traxxas Slash
-Brushed 2WD ARRMA Fury
-No added weight, anywhere or of any kind.
-No cutting or grinding the chassis or any of the parts that attach to it for any reason. All the screws must be used in the top deck/center brace.
-All parts must remain as the manufacturer intended.
Electronics:
-Radio: Open
-ESC/Receiver: Stock ESC, Open Receiver
-Servo: Stock
-Battery: Any hard case 2S battery
-Motor: Traxxas 12T Titan or ARRMA 28T 380 Sized Brushed Motor
Gearing / Motor Plate:
-Stock Gearing
Shocks:
-Any shock oil may be used. Original springs only, no upgrade springs, no cutting the springs.
Differentials:
-Grease may be changed in the differentials but must spin freely, no locked diffs.
Approved upgrades and adjustments:
-Any Radio/Receiver
-Any weight shock oil.
-Gluing/Taping the sidewall of the tires are permitted.
-------------------------
Vintage Trans-AM
Chassis:
-Any 4WD Touring Chassis
Ride Height Specification:
-Minimum ride height is 5mm
Weight Specification:
-Minimum 1400g in race-ready trim
Battery Specifications:
-ROAR approved 7.4v- 7.6v 2 cell LiPo hard cased, 6000mAh MAX limit. 8.40v is maximum voltage allowed. All house track rules regarding LiPo usage apply.
Approved ESCs:
-ANY ESC that is ROAR approved and using ROAR approved “Blinky” spec software or on this list
Tire & Wheel Specifications:
-The only tires allowed are PROTOform VTA Rear Tires (31mm)- #10139-00 and PROTOform VTA Front Tires (26mm)- #10140-00, OR Gravity RC G-Spec VTA Tires #GRC146 using stock tire inserts provided with tire and any HPI, Protoform or Gravity Vintage wheels designed to fit these tires. All other tires and/or part numbers are illegal.
-Wheels and tires designated as "front" must be used as front tires/wheels, "rear" wheels/tires must be used as rears. Five or Eight spoke wheels available in various colors.
-0mm offset front wheels and 6mm offset rear wheels are intended for 26mm width fronts and 31mmwidth rear tires. HPI 8-spoke Vintage wheels from #3805 through #3814, 5-spoke Vintage wheels from #3815 through #3822 and Vintage stock car wheels from #3854 through #3860, Vintage Wheel CC Type #33472 and #33473, Vintage Wheel DTP Type #33474 and #33475 are all legal wheels. Protoform wheels 2766-03, 2766-04, 2765-03, 2765-04 are all legal wheels. Gravity RC GRC147W and GRC147B are all legal wheels.
-Grinding of tire tread is NOT permitted. Sanding of mold seam to remove seam is allowed.
-Tire traction compounds are at the discretion of the track.
-No other altering, changing or softening of the tire is allowed. No "double stuffing" of foam inserts allowed—only single stock vintage tire inserts are allowed.
Body Specifications:
-Late '60s to early '70s American pony car Vintage Trans-Am bodies only
-Body provided deck lid spoilers allowed (not wings).
-Altering the body for the purpose of lightening by sanding, scraping, or any other method is illegal.
-All cars must include a three dimensional driver figure consisting of at least a head and shoulders.
Motor Specifications:
-Gravity GRC2025 SCALE SPEC 25.5 (30deg fixed timing) is the legal motor.
-No modifications or optional parts allowed on motor can, endbell, stator, or rotor No cooling holes or other changes allowed to motor.
-Fans and external clip on heatsinks are allowed, but integral type heatsinks/fans including but not limited to those that require motor disassembly to mount are illegal.